New in version 2.1.
| Removed in Ansible: | |
|---|---|
| version: 2.9 | |
| Why: | Replaced with common *_l3_interface network modules. |
| Alternative: | Use nxos_l3_interface instead. |
Parameter |
Choices/Defaults |
Comments |
|---|---|---|
|
addr
|
|
IPv4 or IPv6 Address.
|
|
allow_secondary
(added in 2.4) |
|
Allow to configure IPv4 secondary addresses on interface.
|
|
dot1q
(added in 2.5) |
|
Configures IEEE 802.1Q VLAN encapsulation on the subinterface. The range is from 2 to 4093.
|
|
interface
required |
|
Full name of interface, i.e. Ethernet1/1, vlan10.
|
|
mask
|
|
Subnet mask for IPv4 or IPv6 Address in decimal format.
|
|
provider
|
|
Deprecated
Starting with Ansible 2.5 we recommend using
connection: network_cli.This option is only required if you are using NX-API.
For more information please see the NXOS Platform Options guide.
A dict object containing connection details.
|
|
username
|
|
Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate either the CLI login or the nxapi authentication depending on which transport is used. If the value is not specified in the task, the value of environment variable
ANSIBLE_NET_USERNAME will be used instead. |
|
ssh_keyfile
|
|
Specifies the SSH key to use to authenticate the connection to the remote device. This argument is only used for the cli transport. If the value is not specified in the task, the value of environment variable
ANSIBLE_NET_SSH_KEYFILE will be used instead. |
|
use_proxy
(added in 2.5) |
|
If
no, the environment variables http_proxy and https_proxy will be ignored. |
|
host
required |
|
Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
|
|
timeout
(added in 2.3) |
Default:
10
|
Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error. NX-API can be slow to return on long-running commands (sh mac, sh bgp, etc).
|
|
use_ssl
|
|
Configures the transport to use SSL if set to true only when the
transport=nxapi, otherwise this value is ignored. |
|
password
|
|
Specifies the password to use to authenticate the connection to the remote device. This is a common argument used for either cli or nxapi transports. If the value is not specified in the task, the value of environment variable
ANSIBLE_NET_PASSWORD will be used instead. |
|
validate_certs
|
|
If
no, SSL certificates will not be validated. This should only be used on personally controlled sites using self-signed certificates. If the transport argument is not nxapi, this value is ignored. |
|
port
|
Default:
0 (use common port)
|
Specifies the port to use when building the connection to the remote device. This value applies to either cli or nxapi. The port value will default to the appropriate transport common port if none is provided in the task. (cli=22, http=80, https=443).
|
|
transport
required |
Default:
cli
|
Configures the transport connection to use when connecting to the remote device. The transport argument supports connectivity to the device over cli (ssh) or nxapi.
|
|
state
|
|
Specify desired state of the resource.
|
|
tag
(added in 2.4) |
Default:
no
|
Route tag for IPv4 or IPv6 Address in integer format.
|
|
version
|
|
Version of IP address. If the IP address is IPV4 version should be v4. If the IP address is IPV6 version should be v6.
|
Note
- name: Ensure ipv4 address is configured on Ethernet1/32
nxos_ip_interface:
interface: Ethernet1/32
transport: nxapi
version: v4
state: present
addr: 20.20.20.20
mask: 24
- name: Ensure ipv6 address is configured on Ethernet1/31
nxos_ip_interface:
interface: Ethernet1/31
transport: cli
version: v6
state: present
addr: '2001::db8:800:200c:cccb'
mask: 64
- name: Ensure ipv4 address is configured with tag
nxos_ip_interface:
interface: Ethernet1/32
transport: nxapi
version: v4
state: present
tag: 100
addr: 20.20.20.20
mask: 24
- name: Ensure ipv4 address is configured on sub-intf with dot1q encapsulation
nxos_ip_interface:
interface: Ethernet1/32.10
transport: nxapi
version: v4
state: present
dot1q: 10
addr: 20.20.20.20
mask: 24
- name: Configure ipv4 address as secondary if needed
nxos_ip_interface:
interface: Ethernet1/32
transport: nxapi
version: v4
state: present
allow_secondary: true
addr: 21.21.21.21
mask: 24
Common return values are documented here, the following are the fields unique to this module:
Key |
Returned |
Description |
|---|---|---|
|
changed
boolean
|
always |
check to see if a change was made on the device
Sample:
True
|
|
commands
list
|
always |
commands sent to the device
Sample:
['interface ethernet1/32', 'ip address 20.20.20.20/24 secondary tag 100']
|
|
end_state
dict
|
always |
k/v pairs of IP attributes after module execution
Sample:
{'interface': 'ethernet1/32', 'prefixes': ['11.11.0.0/17', '20.20.20.0/24'], 'type': 'ethernet', 'addresses': [{'tag': 101, 'mask': 17, 'addr': '11.11.11.11', 'secondary': False}, {'tag': 100, 'mask': 24, 'addr': '20.20.20.20', 'secondary': True}], 'vrf': 'default'}
|
|
existing
dict
|
always |
k/v pairs of existing IP attributes on the interface
Sample:
{'interface': 'ethernet1/32', 'prefixes': ['11.11.0.0/17'], 'type': 'ethernet', 'addresses': [{'tag': 101, 'mask': 17, 'addr': '11.11.11.11', 'secondary': False}], 'vrf': 'default'}
|
|
proposed
dict
|
always |
k/v pairs of parameters passed into module
Sample:
{'interface': 'Ethernet1/32', 'allow_secondary': True, 'mask': '24', 'addr': '20.20.20.20', 'tag': 100}
|
This module is flagged as deprecated and will be removed in version { deprecated[‘removed_in’] | default(‘’) | string | convert_symbols_to_format }@. For more information see DEPRECATED.
Hint
If you notice any issues in this documentation you can edit this document to improve it.