junos_linkagg - Manage link aggregation groups on Juniper JUNOS network devices¶

New in version 2.4.

Synopsis
- Requirements
Parameters
Notes
Examples
Return Values
Status
- Support
- Author

Synopsis ¶

This module provides declarative management of link aggregation groups on Juniper JUNOS network devices.

Requirements ¶

The below requirements are needed on the host that executes this module.

ncclient (>=v0.5.2)

Parameters ¶

Parameter	Choices/Defaults	Comments
active	Choices: yes ← no Default: yes	Specifies whether or not the configuration is active or deactivated
aggregate		List of link aggregation definitions.
description		Description of Interface.
device_count		Number of aggregated ethernet devices that can be configured. Acceptable integer value is between 1 and 128.
members required		List of members interfaces of the link aggregation group. The value can be single interface or list of interfaces.
min_links		Minimum members that should be up before bringing up the link aggregation group.
mode	Choices: on off active passive Default: no	Mode of the link aggregation group. A value of `on` will enable LACP in `passive` mode. `active` configures the link to actively information about the state of the link, or it can be configured in `passive` mode ie. send link state information only when received them from another link. A value of `off` will disable LACP.
name required		Name of the link aggregation group.
provider		Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli` or `connection: netconf`. For more information please see the Junos OS Platform Options guide. A dict object containing connection details.
username		Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
host required		Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
ssh_keyfile		Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
timeout	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
password		Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
port	Default: 22	Specifies the port to use when building the connection to the remote device. The port value will default to the well known SSH port of 22 (for `transport=cli`) or port 830 (for `transport=netconf`) device.
state	Choices: present ← absent up down	State of the link aggregation group.

Notes ¶

Note

This module requires the netconf system service be enabled on the remote device being managed.
Tested against vSRX JUNOS version 15.1X49-D15.4, vqfx-10000 JUNOS Version 15.1X53-D60.4.
For information on using CLI and netconf see the Junos OS Platform Options guide
For more information on using Ansible to manage network devices see the Ansible Network Guide
For more information on using Ansible to manage Juniper network devices see https://www.ansible.com/ansible-juniper.

Examples ¶

- name: configure link aggregation
  junos_linkagg:
    name: ae11
    members:
      - ge-0/0/5
      - ge-0/0/6
      - ge-0/0/7
    lacp: active
    device_count: 4
    state: present

- name: delete link aggregation
  junos_linkagg:
    name: ae11
    members:
      - ge-0/0/5
      - ge-0/0/6
      - ge-0/0/7
    lacp: active
    device_count: 4
    state: delete

- name: deactivate link aggregation
  junos_linkagg:
    name: ae11
    members:
      - ge-0/0/5
      - ge-0/0/6
      - ge-0/0/7
    lacp: active
    device_count: 4
    state: present
    active: False

- name: Activate link aggregation
  junos_linkagg:
    name: ae11
    members:
      - ge-0/0/5
      - ge-0/0/6
      - ge-0/0/7
    lacp: active
    device_count: 4
    state: present
    active: True

- name: Disable link aggregation
  junos_linkagg:
    name: ae11
    state: down

- name: Enable link aggregation
  junos_linkagg:
    name: ae11
    state: up

Return Values ¶

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
diff string	when configuration is changed and diff option is enabled.	Configuration difference before and after applying change. Sample: [edit interfaces] + ge-0/0/6 { + ether-options { + 802.3ad ae0; + } + } [edit interfaces ge-0/0/7] + ether-options { + 802.3ad ae0; + } [edit interfaces] + ae0 { + description "configured by junos_linkagg"; + aggregated-ether-options { + lacp { + active; + } + } + }

Status ¶

This module is flagged as preview which means that it is not guaranteed to have a backwards compatible interface.

Support ¶

For more information about Red Hat’s support of this module, please refer to this Knowledge Base article

Author ¶

Ganesh Nalawade (@ganeshrn)

Hint

If you notice any issues in this documentation you can edit this document to improve it.