eos_eapi - Manage and configure Arista EOS eAPI.¶

New in version 2.1.

Synopsis
- Requirements
Parameters
Notes
Examples
Return Values
Status
- Support
- Author

Synopsis ¶

Use to enable or disable eAPI access, and set the port and state of http, https, local_http and unix-socket servers.
When enabling eAPI access the default is to enable HTTP on port 80, enable HTTPS on port 443, disable local HTTP, and disable Unix socket server. Use the options listed below to override the default configuration.
Requires EOS v4.12 or greater.

Requirements ¶

The below requirements are needed on the host that executes this module.

EOS v4.12 or greater

Parameters ¶

Parameter	Choices/Defaults	Comments
auth_pass		Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli` and `become: yes` with `become_pass`. This option is only required if you are using eAPI. For more information please see the EOS Platform Options guide. Specifies the password to use if required to enter privileged mode on the remote device. If authorize is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTH_PASS` will be used instead.
authorize	Choices: no ← yes	Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli` and `become: yes`. This option is only required if you are using eAPI. For more information please see the EOS Platform Options guide. Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTHORIZE` will be used instead.
config (added in 2.2)		The module, by default, will connect to the remote device and retrieve the current running-config to use as a base for comparing against the contents of source. There are times when it is not desirable to have the task get the current running-config for every task in a playbook. The config argument allows the implementer to pass in the configuration to use as the base config for comparison.
http	Choices: no ← yes	The `http` argument controls the operating state of the HTTP transport protocol when eAPI is present in the running-config. When the value is set to True, the HTTP protocol is enabled and when the value is set to False, the HTTP protocol is disabled. By default, when eAPI is first configured, the HTTP protocol is disabled. aliases: enable_http
http_port	Default: 80	Configures the HTTP port that will listen for connections when the HTTP transport protocol is enabled. This argument accepts integer values in the valid range of 1 to 65535.
https	Choices: no yes ←	The `https` argument controls the operating state of the HTTPS transport protocol when eAPI is present in the running-config. When the value is set to True, the HTTPS protocol is enabled and when the value is set to False, the HTTPS protocol is disabled. By default, when eAPI is first configured, the HTTPS protocol is enabled. aliases: enable_https
https_port	Default: 443	Configures the HTTP port that will listen for connections when the HTTP transport protocol is enabled. This argument accepts integer values in the valid range of 1 to 65535.
local_http	Choices: no ← yes	The `local_http` argument controls the operating state of the local HTTP transport protocol when eAPI is present in the running-config. When the value is set to True, the HTTP protocol is enabled and restricted to connections from localhost only. When the value is set to False, the HTTP local protocol is disabled. Note is value is independent of the `http` argument aliases: enable_local_http
local_http_port	Default: 8080	Configures the HTTP port that will listen for connections when the HTTP transport protocol is enabled. This argument accepts integer values in the valid range of 1 to 65535.
provider		Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli`. This option is only required if you are using eAPI. For more information please see the EOS Platform Options guide. A dict object containing connection details.
username		Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate either the CLI login or the eAPI authentication depending on which transport is used. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
authorize	Choices: no ← yes	Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTHORIZE` will be used instead.
ssh_keyfile		Specifies the SSH keyfile to use to authenticate the connection to the remote device. This argument is only used for cli transports. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
use_proxy (added in 2.5)	Choices: no yes ←	If `no`, the environment variables `http_proxy` and `https_proxy` will be ignored.
auth_pass		Specifies the password to use if required to enter privileged mode on the remote device. If authorize is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTH_PASS` will be used instead.
host required		Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
timeout	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
use_ssl	Choices: no yes ←	Configures the transport to use SSL if set to true only when the `transport=eapi`. If the transport argument is not eapi, this value is ignored.
password		Specifies the password to use to authenticate the connection to the remote device. This is a common argument used for either cli or eapi transports. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
validate_certs	Choices: no yes	If `no`, SSL certificates will not be validated. This should only be used on personally controlled sites using self-signed certificates. If the transport argument is not eapi, this value is ignored.
port	Default: 0 (use common port)	Specifies the port to use when building the connection to the remote device. This value applies to either cli or eapi. The port value will default to the appropriate transport common port if none is provided in the task. (cli=22, http=80, https=443).
transport required	Choices: eapi cli ←	Configures the transport connection to use when connecting to the remote device.
socket	Choices: no ← yes	The `socket` argument controls the operating state of the UNIX Domain Socket used to receive eAPI requests. When the value of this argument is set to True, the UDS will listen for eAPI requests. When the value is set to False, the UDS will not be available to handle requests. By default when eAPI is first configured, the UDS is disabled. aliases: enable_socket
state	Choices: started ← stopped	The `state` argument controls the operational state of eAPI on the remote device. When this argument is set to `started`, eAPI is enabled to receive requests and when this argument is `stopped`, eAPI is disabled and will not receive requests.
vrf (added in 2.2)	Default: default	The `vrf` argument will configure eAPI to listen for connections in the specified VRF. By default, eAPI transports will listen for connections in the global table. This value requires the VRF to already be created otherwise the task will fail.

Notes ¶

Note

For information on using CLI, eAPI and privileged mode see the EOS Platform Options guide
For more information on using Ansible to manage network devices see the Ansible Network Guide
For more information on using Ansible to manage Arista EOS devices see the Arista integration page.

Examples ¶

- name: Enable eAPI access with default configuration
  eos_eapi:
    state: started

- name: Enable eAPI with no HTTP, HTTPS at port 9443, local HTTP at port 80, and socket enabled
  eos_eapi:
    state: started
    http: false
    https_port: 9443
    local_http: yes
    local_http_port: 80
    socket: yes

- name: Shutdown eAPI access
  eos_eapi:
    state: stopped

Return Values ¶

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
commands list	always	The list of configuration mode commands to send to the device Sample: ['management api http-commands', 'protocol http port 81', 'no protocol https']
session_name str	when changed is True	The EOS config session name used to load the configuration Sample: ansible_1479315771
urls dict	when eAPI is started	Hash of URL endpoints eAPI is listening on per interface Sample: {'Management1': ['http://172.26.10.1:80']}

Status ¶

This module is flagged as preview which means that it is not guaranteed to have a backwards compatible interface.

Support ¶

For more information about Red Hat’s support of this module, please refer to this Knowledge Base article

Author ¶

Peter Sprygada (@privateip)

Hint

If you notice any issues in this documentation you can edit this document to improve it.